show

Plasma Cutters and Paint Booths Rule!

[MC2006-09]

"The plasma cutter is my favorite tool!" Fabricating floor pans and replacing frame rails and building unibody subframe connectors for a 650 horsepower car. Muscle Car christens it's new col-met paint booth with how-to paint tips like a pro. Then, it's proper "blocking" techniques to get crisp, sharp show winning body lines.

"The plasma cutter is my favorite tool!" Fabricating floor pans and replacing frame rails and building unibody subframe connectors for a 650 horsepower car. Muscle Car christens it's new col-met paint booth with how-to paint tips like a pro. Then, it's proper "blocking" techniques to get crisp, sharp show winning body lines.

Chevrolet Performance

800-577-6888

  • GM Performance 350CID crate engine. Not remanufactured, but new with 4-bolt mains, steel rods,76cc heads, 0.460-inch intake/exhaust lift camshaft, 8.5:1 compression ratio = 290HP and 326 lg-ft torque. All for $1500 new!

  • Many accessories from the stock V-6 with transfer to the V-8, but the flex plate isn't one one of them. So, you'll have to buy a new one and use new bolts to secure it.

  • The wider and deeper 350 is going to be a tight fit in the stock engine bay. It will require headers, and for them to clear, a smaller, higher torque starter is required. Plus, it will resist the extra heat the headers will produce. Kevin bolts it in.

Holley

800-HOLLEY1

  • Holley 2-barrel ProJection electronic fuel injection uses specifically optimized manifold (shown). Its two-injector throttle body hooks up to stock wiring harness, but mixture is user-controlled.

B&M Racing

818-882-6422

  • The rear seal of the trans output shaft can be a major source of fluid leakage. They are inexpensive, so replace it while you have the chance now.

  • The B&M Hole Shot torque converter has a stall speed of 3200 rpm, right in the new powerband of the 350 crate engine. Before mounting it, fill it about 1 qt of transmission fluid.

O'Reilly Auto Parts

800-755-6759

  • Be sure to confirm you are using a correct V-8 water pump for the stock V-6 serpentine belt drive. Ours from O'Reilly's Auto uses a 1988 and newer reverse-rotation water pump for a V-8. Your new engine will overheat is the pump runs the wrong direction. Paul gave this cast iron pump a quick spray of aluminum to dress it up and match the other components.

JTR

925-462-3619

  • Steath Conversions is the parts portion of Jaguars That Run (JTR). Its full swap kit uses new 2.8 liter motor mounts along w/their laser cut engine mounts (shown), transmission spacer, suppport bearing spacer, pinion angle shim, axle set-back kit, oil filter relocation brackets spacers, and two complete manuals that cover both 2- and 4WD drive S-10 V-8 conversions.

  • When you slam a truck the pinion angle changes, and the relationship between the tail shaft and yoke changes, too. Stealth Conversions has all the parts to re-align the driveshaft. Show here is the support bearing spacer, but they have the correct pinion angle shims, too.

Pertronix

909-599-5955

  • This is why you install the distributor indexed to cylinder #1 BEFORE you bolt in the engine. That's all the clearance the Pertronix small-cap distributor has. It uses a separate coil you can mount remote to it.

  • Pertronix also makes Patriot headers for this swap. These are coated inside and out for increased durability for the finish and prevent rusting.

Edge Products

888-360-3343

  • Edge Products has these new higher flow electronic fuel injectors that mate directly to stock GM or Bosch wiring harnesses. They can flow up to 83-lb/hr!

Kelderman Mfg.

800-334-6150

  • Oh boy, with Kelderman's 10--12-inch air lift kit you wil be the biggest and baddest on your block. Fully computerized it has all the parts for you to lift your truck high enough where extra oxygen will be needed. Smaller cars will scurry out of your path!

'69 ZL1 COPO Camaro

MuscleCar teams up with Chevrolet Performance to build a tribute to one of the most legendary muscle cars ever made: a 1969 ZL1 COPO Camaro.

Watch This Build
(Thumbnail image) for build '69 ZL1 COPO Camaro

NOPO to COPO

[MC2013-05]

With the starting point of an iconic Chevrolet Engine, Tommy and Mank set about creating a tribute to one of the world's most desired cars: a 1969 ZL1 COPO Camaro. But before they can build a car-they have to find one! This is the start of an iconic build.

Watch This Episode (Thumbnail image) NOPO to COPO

NOPO to COPO Engine Swap/Shifter Install

[MC2013-06]

An all-aluminum ZL1 Big Block gets plugged into the '69 COPO Camaro tribute, and the floor is modified to receive a conversion from automatic to 4-speed. Also, find out why trim pieces tend to pit so badly over time, and how to revive a barn find car without catching it on fire!

Watch This Episode (Thumbnail image) NOPO to COPO Engine Swap/Shifter Install

COPO Camaro Suspension

[MC2013-07]

Work continues on the MuscleCar COPO Camaro tribute project as the guys get to work building a suspension system that looks and works like an original high performance 1969 Camaro's would have. Tommy teaches you how to chop down a barn find Impala 12-bolt rear end to fit under a Camaro and Mank works on revitalizing the stock front end components.

Watch This Episode (Thumbnail image) COPO Camaro Suspension

COPO Camaro Gains its Feet

[MC2013-08]

The car has to be converted from automatic to manual floor pedals, and the firewall gets some factory style mods that change the car over to big-block style. Then, everything you ever wanted to know about brake lines and fuel lines.

Watch This Episode (Thumbnail image) COPO Camaro Gains its Feet

COPO Camaro Paint and Body

[MC2013-09]

The guys try out a self-contained paint system on the 1969 COPO Camaro Tribute Project. Starting with body work, all the way through to buffing out the end result, learn how to take your finish from beginning to end.

Watch This Episode (Thumbnail image) COPO Camaro Paint and Body

COPO Camaro 4-Speed Build

[MC2013-10]

Learn how you can take the concept of a classic Muncie 4-Speed and improve on it in every way, shape, and form. Then it's safe glass removal, floor panel prep, and a great way to keep raw metal panels from rusting.

Watch This Episode (Thumbnail image) COPO Camaro 4-Speed Build

COPO Camaro Component Resto

[MC2013-11]

The MuscleCar guys work on rescuing several stock pieces of their 1969 COPO Camaro Tribute Project. A pair of bucket seats with broken frames need some help, a steering column rebuild can save serious bucks, and a garage-fix for a broken plastic grill! Flashback takes a look at our COPO's cousin, another famous '69 Camaro the Z28 RS!

Watch This Episode (Thumbnail image) COPO Camaro Component Resto

COPO Interior and Exhaust

[MC2013-12]

MuscleCar gets to plug in the stock-style interior for their 1969 COPO Camaro tribute project. Then Tommy shows how to address one of the more often neglected parts of a restoration: the inside of the trunk. Then it's exhaust from headers to tailpipes as the guys help the Camaro exhale.

Watch This Episode (Thumbnail image) COPO Interior and Exhaust

COPO to Go!

[MC2013-15]

The MuscleCar guys tie a bow on the COPO Camaro Tribute project by showing how to properly prepare the crate engine for firing, including making your own oil priming tool. Then after a quick lesson in Carb tuning and timing, the COPO Camaro gets to have its day in the sun as the guys see what she can do.

Watch This Episode (Thumbnail image) COPO to Go!

'74 Dodge Dart "Pro-Street Dodge"

MuscleCar takes a 1974 Dodge Dart and builds an Earth-shattering, drag-strip monster!

Watch This Build
(Thumbnail image) for build '74 Dodge Dart "Pro-Street Dodge"

Big Bad Dodge!

[MC2012-06]

Rick and Tom set their sights on a brand-new project, and they have some pretty hefty plans for an old Mopar. Some might consider it a less desirable model, but the guys just might change your mind when you see what they have in store.

Watch This Episode (Thumbnail image) Big Bad Dodge!

Pro Street Dodge Floor Prep & Wiring

[MC2012-16]

The 1974 Dodge Dart, gets some floor preparations done along with wiring. Jamey Jordan stops by to perform some aluminum wizardry, and the guys take a trip to the world's largest Shelby & Ford show.

Watch This Episode (Thumbnail image) Pro Street Dodge Floor Prep & Wiring

Pro Street Dodge Suspension

[MC2012-07]

Rick and Tom get a hankerin' for some suspension work. They unbolt, chop, cut, measure, and install a whole new front and rear suspension set-up for the Dodge Dart, including some Pro help with a back-half kit from one of the leaders in the field. Tommy also hand-fabs a steel Spoiler for the Oldsmobile.

Watch This Episode (Thumbnail image) Pro Street Dodge Suspension

Pro Street Dodge Cage

[MC2012-08]

Tommy and Rick cut up and burn in a drag-style cage kit for the '74 Pro Street Dodge Dart. Then they work up some new sheet metal tubs and flooring to replace what was annihilated when the back-half kit went in.

Watch This Episode (Thumbnail image) Pro Street Dodge Cage

Blown Hemi Shoehorn

[MC2012-11]

The Pro Street Dodge Dart gets a Frankenmotor wedged into it's engine bay - complete with a sky-high blower sticking way up out of the hood! Hollywood movie and tv car builder Steve Mank joins the crew and lends a helping hand.

Watch This Episode (Thumbnail image) Blown Hemi Shoehorn

Dodge Sheet Metal

[MC2012-12]

After cutting most of the floor out of the Pro Street Dodge Dart, the guys are ready to start putting metal back into it. Custom-mounting a set of bumpers and building a one-off exhaust will get the Dodge one step closer to prowling the streets.

Watch This Episode (Thumbnail image) Dodge Sheet Metal

Dodge Dart Fuel and Fire

[MC2012-14]

The Pro Street Dodge Dart gets a fuel system to feed it's blown Hemi, and the guys talk about safety & fire systems.

Watch This Episode (Thumbnail image) Dodge Dart Fuel and Fire

By-Request Builds

[MC2012-15]

Dive into your old carburetor, reinforce your suspension, re-cover your interior, and fix your dents! Steve, Tommy, and Rick take a crack at answering your e-mails and show you how to fix those "personality quirks" on your ride that rub you the wrong way.

Watch This Episode (Thumbnail image) By-Request Builds

Pro Street Dodge Paint and Graphics

[MC2012-18]

The 700 Horsepower Blown Pro Street Dodge, goes from Black to Plastic to Primer to Painted. Learn how to use your computer to make graphics for your ride, and visit a huge Mustang and Shelby show.

Watch This Episode (Thumbnail image) Pro Street Dodge Paint and Graphics

Pro Street Dodge Odds and Ends

[MC2012-19]

The '74 Pro Street Dodge Dart, gets buttoned down as many final details are seen to. Fluids, interior, glass, and a pile of other odds and ends all get the once over as the Dodge is almost ready to go.

Watch This Episode (Thumbnail image) Pro Street Dodge Odds and Ends

It's Business Time!

[MC2013-01]

The Pro Street Dodge Dart, Project Business Time, is ready to drive. The guys show how to lock down your drag tires with a set of rim screws, then it's taking the Dodge for a Slow cruise to check for any problems. Flashback takes a look at another Dart with a tendency towards "swinging", and then Business Time finally hits the track.

Watch This Episode (Thumbnail image) It's Business Time!

'69 Hurst Edition Oldsmobile

MuscleCar starts out with a a 1969 Oldsmobile Cutlast, hoping to rebuild it with inspiration from the classic Hurst Edition Oldsmobile.

Watch This Build
(Thumbnail image) for build '69 Hurst Edition Oldsmobile

Is THIS your Father's Oldsmobile?

[MC2012-02]

Tommy and Rick start a new project, hoping to build it with inspiration from the classic Hurst Edition Oldsmobiles. Also, Year One's Braselton Bash, and the guys do a little paint-mixing wizardry.

Watch This Episode (Thumbnail image) Is THIS your Father's Oldsmobile?

Olds Powder Coat and Quarters

[MC2012-03]

The guys get the Oldsmobile blasted, fix some gnarly quarter panels, and talk tech with the best chassis guy in the business. Also, Flashback takes a look at a super-fine 442.

Watch This Episode (Thumbnail image) Olds Powder Coat and Quarters

Sucker Punch Finale & 461 Oldsmobile Motor Build

[HP2012-07]

This time the finale of Project Sucker Punch, HorsePower's Buick Century station wagon being built as the ultimate sleeper machine. A 461 turbocharged Pontiac engine goes in along with race-ready transmission and the works, before a payoff on the street.

Watch This Episode (Thumbnail image) Sucker Punch Finale & 461 Oldsmobile Motor Build

Oldsmobile Part 3

[MC2012-04]

The Oldsmobile gets planted onto the Art Morrison Chassis, and the guys do some customizing on the body including flush-mounting glass and shaving drip rails. Flashback takes a look at a classic Trans Am.

Watch This Episode (Thumbnail image) Oldsmobile Part 3

Pro Street Dodge Suspension

[MC2012-07]

Rick and Tom get a hankerin' for some suspension work. They unbolt, chop, cut, measure, and install a whole new front and rear suspension set-up for the Dodge Dart, including some Pro help with a back-half kit from one of the leaders in the field. Tommy also hand-fabs a steel Spoiler for the Oldsmobile.

Watch This Episode (Thumbnail image) Pro Street Dodge Suspension

Oldsmobile Rear Bumper Fab and Floor Pans

[MC2012-09]

Tommy shows step-by-step how to do custom metal mods on the Hurst Tribute Oldsmobile's rear bumper, and the guys do engine and tranny mock-up, where they find that some floor modifications have to be made.

Watch This Episode (Thumbnail image) Oldsmobile Rear Bumper Fab and Floor Pans

Oldsmobile Restomod Returns

[MC2013-02]

Tommy and Mank set to work on the Olds Cutlass Hurst Tribute Restomod by making room for an oversized set of custom wheels and tires. Flashback takes a look at a rare Mopar that was built to take the strip by storm, and Mank shows a $20 fix that can be a serious upgrade for your brakes.

Watch This Episode (Thumbnail image) Oldsmobile Restomod Returns

Olds Tank Mods & Glass Etching

[MC2013-03]

The Oldsmobile Restomod Project's fuel tank requires some modification for a serious fuel pump, and the guys show you how to do it. Tommy does some rust repair on a door that is in need of rescue, then Mank and Tommy do some glass etching, with 3 different ways to personalize the glass on your ride.

Watch This Episode (Thumbnail image) Olds Tank Mods & Glass Etching

Custom Firewall and Muscle Car Museum

[MC2013-04]

The guys work on getting a completely custom firewall installed on the 1969 Oldsmobile Hurst Tribute Restomod, with help from car builder Brad Starks. Also, Tommy and Mank take a trip to the Great Smoky Mountains to visit one of the nation's Premiere Muscle Car Museums, where they make some rare finds.

Watch This Episode (Thumbnail image) Custom Firewall and Muscle Car Museum

'86 Ford Mustang "Dark Horse"

MuscleCar picks up an 1986 Ford Mustang and adds some serious upgrades to the wounded pony.

Watch This Build
(Thumbnail image) for build '86 Ford Mustang "Dark Horse"

Fox Body Pony - Part 1

[MC2011-15]

This week on MuscleCar, Tommy heads to the hills to save a wounded Pony. Buick fights back with a turbo that ain't just whistling Dixie! And is that gold in them thar hills? Nah, just paint, and Rick's gonna show you how to spray it.

Watch This Episode (Thumbnail image) Fox Body Pony - Part 1

Dark Horse/ Candy Paint Crash Course

[MC2011-16]

Project Dark Horse gets a stroker motor and suspension upgrades, Tommy rebuilds a Posi-Track, and Rick gives a crash course on paint gun setup and spraying candies.

Watch This Episode (Thumbnail image) Dark Horse/ Candy Paint Crash Course

Dark Horse Top End and Exhaust

[MC2011-17]

Rick and Tommy give Dark Horse's engine a top end and accessories and build a streetable exhaust system. Rick also demonstrates the difference between cast and forged aluminum wheels.

Watch This Episode (Thumbnail image) Dark Horse Top End and Exhaust

Dark Horse Interior Tear-Away

[MC2011-18]

Rick and Tommy tear out Dark Horse's interior to lighten it's load, set it up with new wheels and tires, and weld in a roll cage. Altered E-Go gets prepped for track day by an old friend, and Rick does spot repair on a Camaro hood.

Watch This Episode (Thumbnail image) Dark Horse Interior Tear-Away

Dark Horse Paint & Body

[MC2011-19]

The Fox Body Mustang gets bodywork and paint, Rick and Tommy have fiberglass to fix, emblems to shave, and trim to strip down. Also, Flashback features a rare AMC.

Watch This Episode (Thumbnail image) Dark Horse Paint & Body

Dark Horse Stage 1 Complete!

[MC2012-01]

The finishing touches are put on the Fox Body Mustang, Dark Horse, and then it heads to the track, where the guys run into some issues.

Watch This Episode (Thumbnail image) Dark Horse Stage 1 Complete!

'70 Chevy Camaro RS "Limelight"

A new MuscleCar project is started: transforming a 1970 Camaro RS into a stock-style RS/SS 396.

Watch This Build
(Thumbnail image) for build '70 Chevy Camaro RS "Limelight"

Project Limelight Debut

[MC2011-04]

MuscleCar takes on an all-new project: restoring a 1970 Camaro RS and transforming it into a stock-style RS/SS L78 396 called Project Limelight! The Tribute Trans Am is back to show off its winning combination of classic style and modern muscle. In Flashback, take a ride in a top-condition 1970 Camaro RS/Z28.

Watch This Episode (Thumbnail image) Project Limelight Debut

1970 Camaro Rust Repair and Engine Teardown

[MC2011-05]

Rick and Tommy show how to repair old sheetmetal damage and rust spots. Take a trip to the sandblast shop to find out what Project Limelight looks like in her birthday suit. Tommy cracks open the donor 396 engine and makes some unfortunate discoveries.

Watch This Episode (Thumbnail image) 1970 Camaro Rust Repair and Engine Teardown

Project Limelight Suspension, Brakes and Rear End

[MC2011-07]

Project Limelight gets ungraded stock suspension and a 12-bolt rear end.

Watch This Episode (Thumbnail image) Project Limelight Suspension, Brakes and Rear End

Project Limelight Engine and Transmission

[MC2011-08]

Learn how a block is sleeved when the 396 engine for our 1970 Camaro RS/SS goes to the machine shop. Tommy shows some of the finer points of assembling an engine including file-fitting rings and measuring rod clearance. Rick explains how to convert an auto car to a 4-speed.

Watch This Episode (Thumbnail image) Project Limelight Engine and Transmission

Project Limelight Paint, Stripes and Wheels Refurb

[MC2011-09]

The 1970 Camaro RS/SS gets an era-appropriate coat of lime green, living up to the name Project Limelight! Learn how to refurbish an original set of painted steel wheels, including the trim rings. Find out how stripes are added over clear-coat.

Watch This Episode (Thumbnail image) Project Limelight Paint, Stripes and Wheels Refurb

Project Limelight Engine Accesories & Fiberglass Hood Paint

[MC2011-10]

Learn how to install wiring and interior parts, including a bow-style headliner, as work continues on the 1970 Camaro. Rick shows how to re-foam and install seat covers on original seat frames.

Watch This Episode (Thumbnail image) Project Limelight Engine Accesories & Fiberglass Hood Paint

Project Limelight Engine Accessories & Hood Paint

[MC2011-11]

Project Limelight's engine is decked out with the final details under the hood. Rick shows how to paint and install an aftermarket fiberglass hood on any car.

Watch This Episode (Thumbnail image) Project Limelight Engine Accessories & Hood Paint

Project Limelight Payoff

[MC2011-12]

The 1970 Camaro RS/SS gets some finishing touches, then the guys pull an all-nighter getting the motor to start and run.

Watch This Episode (Thumbnail image) Project Limelight Payoff

Project Limelight Goes for a Drive/GoodGuy's

[MC2011-14]

On this episode of MuscleCar, Rick and Tommy take Limelight out for a spin and visit one of the biggest classic car shows in the country. Rick shows some of the biggest mistakes painters make on their own rides.

Watch This Episode (Thumbnail image) Project Limelight Goes for a Drive/GoodGuy's

'73 Buick Century "Blue Collar Buick"

With a restoration budget of $10K, MuscleCar has practical performance plans for its 1973 Buick Century, Project "Blue Collar Buick".

Watch This Build
(Thumbnail image) for build '73 Buick Century "Blue Collar Buick"

Blue Collar Buick Roof and Rust

[MC2010-05]

Rick and Tommy show how to replace the entire roof on the '73 Buick. Rick demonstrates rust repair on the window channel, and "Project Dead Goat" terrorizes the neighborhood.

Watch This Episode (Thumbnail image) Blue Collar Buick Roof and Rust

Blue Collar Buick Bumpers and Door Handles

[MC2010-10]

Project Blue Collar Buick loses some serious weight from the front and rear bumpers. Rick shows how to graft in different door handles. Flashback features a 1965 Dodge Coronet S/S.

Watch This Episode (Thumbnail image) Blue Collar Buick Bumpers and Door Handles

Blue Collar Buick Tail Lights

[MC2010-11]

Rick replaces the tail panel on Project Blue Collar Buick, and designs some one-off budget tail lights using some unusual materials. Tommy shows how to save your car's old glass by polishing out scratches and haze. Flashback showcases a 1968 El Camino SS.

Watch This Episode (Thumbnail image) Blue Collar Buick Tail Lights

Blue Collar Front Suspension

[MC2010-12]

MuscleCar continues the budget-minded Blue Collar Buick build with front-end maintenance and inexpensive upgrades. Learn how to bring a points distributor back to life, or install a kit to convert one to electronic ignition. Flashback hits the road in a 1971 Dodge Super Bee.

Watch This Episode (Thumbnail image) Blue Collar Front Suspension

Blue Collar Engine Compartment Makeover

[MC2010-15]

Project Blue Collar Buick gets an amazing under-hood transformation that's cheap and easy to achieve. The big-block 455 Buick engine roars to life for the first time, and Flashback features a 1969 Camaro Z-28 Rally Sport.

Watch This Episode (Thumbnail image) Blue Collar Engine Compartment Makeover

Blue Collar Air Cleaner and Gas Tank

[MC2010-17]

Rick and Tommy design and build a trick custom air cleaner for Blue Collar Buick, and Rick shows his flair with the air brush to finish it out. Tommy shows how to clean and seal an old gas tank. Flashback showcases a '70 1/2 King Cobra Super Spoiler prototype.

Watch This Episode (Thumbnail image) Blue Collar Air Cleaner and Gas Tank

Blue Collar Buick Paint

[MC2010-18]

The '73 Buick Century turns over a new leaf with a screaming orange and sinister charcoal paint scheme. Along the way, Rick and Tommy drop plenty of valuable tips on blocking for paint and two-tone layout. In Flashback, take a ride in a 1970 Challenger TA.

Watch This Episode (Thumbnail image) Blue Collar Buick Paint

Blue Collar Buick Interior and Payoff

[MC2010-22]

Learn how to refresh an interior on a budget with tips on dash pad and seat repair, dyeing vinyl, fabricating panels, and refurbing original parts. Project Blue Collar Buick hits the road for the first time. Flashback features a 1970 Buick GS.

Watch This Episode (Thumbnail image) Blue Collar Buick Interior and Payoff

Blue Collar Buick Upgrades Part 1

[MC2011-02]

We're notching up the performance on Project Blue Collar Buick, and a new cam, heads, intake and carb are just the beginning! Learn how to measure for custom pushrods, and how to correctly install a torque converter. Flashback features a rare 1966 Olds 442 W30.

Watch This Episode (Thumbnail image) Blue Collar Buick Upgrades Part 1

Blue Collar Buick Upgrades Part 2

[MC2011-03]

The Buick gets a new rear end that will stand up to increased horsepower. Rick shows how to install a disc brake conversion, then Blue Collar makes a dyno run to see if the performance upgrades brought us up to our goal. Tommy installs a hood tach, then takes the Buick on a road trip to the GS Nationals and hits the drag strip.

Watch This Episode (Thumbnail image) Blue Collar Buick Upgrades Part 2

Project Blue Collar Buick Debut

[MC2010-04]

MuscleCar unveils the plans for Project Blue Collar Buick, a '73 Century with a restoration budget of under $10K. The guys go on an engine-hunt, bring back a Buick 455, and tear it down before sending it to the machine shop.

Watch This Episode (Thumbnail image) Project Blue Collar Buick Debut

'67 Pontiac LeMans

MuscleCar clones a Pontiac GTO from a 1967 LeMans.

Watch This Build
(Thumbnail image) for build '67 Pontiac LeMans

Superbird, EPA Turn Coat

[MC2007-11]

Watch automotive history unfold as Lou discovers a lost Plymouth Superbird built by the legendary NASCAR builder Ray Nichels! Designed for the Environmental Protection Agency, this Superbird chased commercial jets down the tarmac for emissions testing and was responsible for proving that leaded gas was harmful to the environment.

Watch This Episode (Thumbnail image) Superbird, EPA Turn Coat

Pontiac LeMans-Refurbishing the Frame

[MC2007-12]

It's back on the Pontiac LeMans restoration and rusty, bent frame is no problem for Lou. He'll show you how to turn a pressure sprayer into a sandblaster making it easy to remove years of weathering and a basic way to straighten your frame.

Watch This Episode (Thumbnail image) Pontiac LeMans-Refurbishing the Frame

Pontiac LeMans-Stroker Build-Up

[MC2007-13]

The LeMans frame is finished up and it's time to take a tired stock motor and turn it into a powerful stroker...all on this week's MuscleCar.

Watch This Episode (Thumbnail image) Pontiac LeMans-Stroker Build-Up

Pontiac LeMans Complete Body Work

[MC2007-16]

Lou and company virtually start over on the '67 LeMans body. We strip it to it bones and get ready for the rising, in fact they almost building a body from scratch.

Watch This Episode (Thumbnail image) Pontiac LeMans Complete Body Work

Project '67 LeMans Body Fabrication & Repair

[MC2007-17]

Lou challenges himself with some very difficult body fabrication and repair on what little we salvaged from our '67 Le Mans body.

Watch This Episode (Thumbnail image) Project '67 LeMans Body Fabrication & Repair

Manual Transmission Re-build

[MC2007-23]

A profile on a bolt on sub-frame connector, re-building a manual transmission and do it yourself under coating.

Watch This Episode (Thumbnail image) Manual Transmission Re-build

Project LeMans Goes Gold

[MC2008-01]

Project LeMans stays on budget by saving some old parts, Rick "The Arsonist" Bacon joins the MuscleCar team. Rick and Brent prep and paint the LeMans, Lou installs the brake and fuel plumbing, exhaust, and under/overdrive unit. Flashback showcases a 1977 Pontiac CanAm.

Watch This Episode (Thumbnail image) Project LeMans Goes Gold

Project LeMans Interior

[MC2008-04]

Project LeMans gets an interior makeover. Lou tackles the wiring while Rick refurbs the steering wheel and column. Brent shows how powder-coating is done. Flashback takes us for a ride in a 1969 Mach 1 Mustang.

Watch This Episode (Thumbnail image) Project LeMans Interior

Project Red Sled Debut

[MC2008-08]

Rick and Mike Galley roll in MuscleCar's next challenge, a '61 Impala that will become Project Red Sled. Find out how to blow a car apart the right way. The LeMans gets its finishing touches, and a classic car appraiser tells us how much it's worth.

Watch This Episode (Thumbnail image) Project Red Sled Debut

'70 Chevy Nova "Old Blue Hair"

A low-mileage 1970 Chevy Nova gets a 440hp GM crate engine upgrade!

Watch This Build
(Thumbnail image) for build '70 Chevy Nova "Old Blue Hair"

That Perfect Finish

[MC2006-14]

Jared shows how to get the Crate Camaro's paint just right with tools and techniques that you can use on your own muscle car. Lou demonstrates what to look for when you're buying a project car and we profile one of the most outrageous muscle cars ever built - the Plymouth Superbird.

Watch This Episode (Thumbnail image) That Perfect Finish

Project Blue Hair Engine Swap

[MC2006-19]

Our all-original, low-mileage '70 Nova gets a 440hp GM crate engine - but the swap is not as simple as it sounds. And we'll see some Buick muscle... from the Buick Horsepower Nationals in Indianapolis.

Watch This Episode (Thumbnail image) Project Blue Hair Engine Swap

Project Blue Hair Part 2

[MC2006-20]

Our 33,000-mile original '70 Nova continues on the path to greatness! Lou finishes the motor and tranny installation and puts air suspension in the front - all without changing the stock look. And our "Flashback" segment profiles a rare Mopar - the 69 Road Runner 440 Six-Pack.

Watch This Episode (Thumbnail image) Project Blue Hair Part 2

Project Old Blue Hair 'Sleeper' Wakes Up

[MC2007-01]

Project "Blue Hair" gets an LS364 crate motor, new gas tank and fuel system. Once completed, Lou installs frame connectors to stiffen up the body and wires up the ignition system. Flashback segment covers the 1967 Chevy Camaro Indy 500 official pace car!

Watch This Episode (Thumbnail image) Project Old Blue Hair 'Sleeper' Wakes Up

Old Blue Hair Gets in Gear Wth a Beefed Up Rear End

[MC2007-02]

Project "Blue Hair" is outfitted with a high performance rear end including carbon steel axles, 4:10 gearing and a posi-trac unit . Lou teaches you how to build your own super stock springs at home and the LS364 gets a cooling system with a custom serpentine setup. And in our Musclecar Flashback segment we look back at the Mercury Cyclone!

Watch This Episode (Thumbnail image) Old Blue Hair Gets in Gear Wth a Beefed Up Rear End

Final Day for Old Blue Hair

[MC2007-03]

Project "Blue Hair" is set up to receive a new flywheel and clutch. Lou fabricates a transmission tunnel to accept the Rockland T-6 trans and a little interior modification helps with the "sleeper" look. A new set of wheels put's "Blue Hair" back on her feet! Musclecar's flashback segment looks at AMC's SC/Scrambler!

Watch This Episode (Thumbnail image) Final Day for Old Blue Hair

Raunchy Rat Pay Off & Old Blue Hair Motor Upgrades!

[HP2007-11]

The HorsePower Raunchy Rat project climaxes with Joe and Mike putting the finishing touches. Then MuscleCar's Project Blue Hair makes an appearance to get a makeover of its LS2 engine. And as the days get longer, Joe lets you in on some warm weather events across the country including Summer Nights in Kentucky and a host of Good Guys events all over the country!

Watch This Episode (Thumbnail image) Raunchy Rat Pay Off & Old Blue Hair Motor Upgrades!
Join the myPowerBlock family today!

POWERBLOCKTV

COMPANY

SOCIAL&APPS